Hey guys, I just launched a new site that may be of your interest. It’s called Plamo Swap Meet and basically, you can just sell your kits through the site for no cost at all. They can be in whatever condition and is very similar to eBay except its just for model kits.
I know it’s no surprise that we modeler’s have backlogs (sometimes mountains of…[Read more]
Hey guys, I just launched a new site that may be of your interest. It’s called Plamo Swap Meet and basically, you can just sell your kits through the site for no cost at all. They can be in whatever condition and is very similar to eBay except its just for model kits.
I know it’s no surprise that we modeler’s have backlogs (sometimes mountains of…[Read more]
Hey guys, I just launched a new site that may be of your interest. It’s called Plamo Swap Meet and basically, you can just sell your kits through the site for no cost at all. They can be in whatever condition and is very similar to eBay except its just for model kits.
I know it’s no surprise that we modeler’s have backlogs (sometimes mountains of…[Read more]
The Jesta HG Cannon looks pretty sick. I would recommend an RG Kit but most of them are 2000 yen with of them being 2400. What kind of design are you looking for? Military look, more swords, more guns etc.?
Yes, exactly what I was looking for, and high grade kits are supposed to be really good! Thanks!
I prefer a more military look, after all, why would you bring a knife to a gunfight?
Which RG kit has dry-transfer decals?
But yeah I agree with Savvi, I hope they include water -slide decals in more kits. I’m terrible with dry-transfers – I always mess them up.
1. No it’s not really necessary. I don’t sand my kits, I just apply a coat of primer of the pieces for the paint to stick onto the piece.
2. I would say airbrush for all of them because unless you’ve been practicing for a long time or are willing to do many hours of sitting and painting light coats of paints with a hand brush, airbrush will yield…[Read more]
Thanks heaps for the suggestion and reply. Yeah that would be pretty annoying. I was actually thinking of going to gentaikits for replacement parts but it could get pretty pricey or try and reshape them myself even though it’s a little risky. But yeah Vegeta does really great work.
Luckily I contacted the HLJ Parts department and they said that…[Read more]
It’s been a while since my last assembled kit. So I decided to jump the bandwagon and start building my MG Nu Gundam Ver. Ka. Iv’e had it sitting in the wardrobe for a while now and decided now is the time.
Hey guys, I was building my MG Nu Gundam Ver. Ka and much to my surprise Bandai decided to throw me challenge. There is a runner that has a total of 8 pieces that have been affected by a molding issue (I think it’s related to the cool down time and handling). It’s definitely a runner that should not have passed in the product quality process. Any…[Read more]
you know i am building the same kit and one of the hands had a whole lot of extra plastic all over the fingers and the part that you use to help hold the weapons. i was able to clean up most of the extra plastic around the fingers and they work fine if a little tighter than normal, but the attachment piece was a loss. it wouldn’t rotate no matter…[Read more]
Thanks heaps for the suggestion and reply. Yeah that would be pretty annoying. I was actually thinking of going to gentaikits for replacement parts but it could get pretty pricey or try and reshape them myself even though it’s a little risky. But yeah Vegeta does really great work.
Luckily I contacted the HLJ Parts department and they said that…[Read more]
No, that’s plenty big. I use a .2mm needle with enamels and have so far not encountered a single clogging problem. Just make sure that the paints are properly thinned.
The Krome comes with a .2mm and a .3mm so that will serve you very well. You can use the .3mm for metallics as they are usually a little thicker .