-
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 11 months agoAnd now to interior,..the interior tub is missing the door lever, so planned to create them. Some masking tape have been cut and placed to mark where the drill bits are supposed to get through….Plus two strip of plastic are in place to mount the seat belt hanger… -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 11 months ago -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 11 months agoNow to fix the tie rod…, the tie rod can be installed by removing some material beneath, to allow it to be freely movable to each side -
fourground posted a new activity comment 5 years, 11 months ago
Like the sketch, draw and then build, excellent bro
-
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 11 months ago -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 11 months agoThe legs setting eventually done, as the two pictures showed before and after final setting is done -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 11 months ago -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 11 months agoThe body shell painted black and clear coated, using TS can and the roof plus the the deck lid have been polished as the picture below -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 5 years, 12 months agoI begin to setting all the suspension arms when front upper arms broke off during test fit. Got no choice, I have to fix the broken parts with a little piece of music wire as the bone to fortify the joint -
fourground posted an update 6 years ago
And the appearance in its place…. -
fourground posted an update 6 years ago
This is what the new caliper looked after it had been separated from the donor brakes and carved the inner middle section out to give some space for the spinning rotors… -
fourground posted a new activity comment 6 years ago
Thanks mate
-
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoTo make the brake rotors spin with the wheels, I will use bigger brake calipers from my parts box replacing the little old ones, ….. -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoAfter the drill…. -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoThe troubled brake rotor has been fixed, by laying consecutively spread of super glue until it bring back the correct shape…. -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoThe stock brakes are too small for the new wheels, so I replaced them with aftermarket ones with calipers moulded in. I missed a cut when shaving the moulded caliper and leaving a jagged edge where the caliper was -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoThe stance so far…… -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoSince the construction of the stock wheels fitting is pretty weak, then I choose to convert the joint of the wheels from female to male pins…, the centre of those wheels were drilled … -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoAs for rear wheels, the spacers need to be fixed in an angle similar to what at the front wheel.. -
fourground posted an update in the group
Intermediate Modeler – Modeling Competition 2017 6 years agoThe front uprights just need to be rotated from outside to inside and voila… You’ve got the correct stance - Load More
fourground
